Top 10 typical forklift mishaps ， forklift operation ought to take note of these matters ！.

Do not underestimate the forklift at the office. If the procedure is bad, there will certainly be significant accidents in minutes, and there are many accidents involving forklifts.

Case 1: The forklift cargo blocked the chauffeur's sight, and the person in front could not be found, resulting in a rolling accident.
Instance 2: In order to maintain the balance of the forklift when raising hefty items, the workers utilized their body weight as the counterweight, which practically caused casualties.
Case 3: The size of the forklift freight goes beyond the permitted width of the route and holds on the roadside rack, which nearly triggers an accident.
Case 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift driver did not see the pedestrian, and the pedestrian did not see the forklift.
Situation 6: The forklift lifts the personnel unlawfully, the forklift chauffeur does not wear the safety belt, the forklift lifter drops and the chauffeur is crushed when the forklift surrender.
Situation 7: The forklift driver did not put on a seat belt and fell from the lorry when it rolled over and was crushed.
Forklift procedure ought to take note of these matters ：.

Start.
1. Before beginning, observe the surroundings, and after confirming that there are no barriers that hinder the safety and security of driving, beep the horn first and after that start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale should be secure before beginning.
3. When the forklift starts with a lots, the chauffeur needs to first validate that the tons is stable and trustworthy.
4. The start has to be slow and consistent.

Driving.
1. When driving, the height between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole should be tilted in reverse. .
2. Do not lift the fork too expensive when driving. When getting in and leaving the job website or while driving, take care that there will be no challenges overhead. When the load is traveling, the fork has to not be raised expensive, which will impact the security of the forklift. .
3. After dumping, the fork should be reduced to the regular driving placement before driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal should be issued first. High-speed doglegs are banned. High-speed sharp turns will cause the automobile to shed side security and tip over. .
5. When the forklift is downhill, it is strictly forbidden to shut off the flame and slide, and it is prohibited to brake instantly while driving with lots unless there are unique situations.
6. When the forklift is running, it should follow the website traffic rules in the manufacturing facility and have to maintain a particular safety distance from the vehicle in front. .
7. When the forklift is running, the load must be in the lowest position that does not hinder the driving, and the gantry should be correctly tilted back. The load shall not be elevated other than when piling or filling. .
8. The elevation of the tons must not obstruct the motorist's view. In special scenarios, when the product impacts the forward vision, drive at a low speed when reversing.
9. It is restricted to activate the ramp, neither to drive across the ramp. .
10. The safe driving speed of the forklift in the manufacturing facility location is 5 km/h, and it needs to drive safely at a low rate when entering the manufacturing workshop location. .
11. When the forklift is lifted, lifted or driven, it is forbidden for workers to stand on the fork to hold things and play a stabilizing function. .
12. If problems are located, they will certainly be repaired and reported in a prompt fashion, and they will never ever run with diseases or conceal them.

filling and discharging.
1. When fork-loading items, the range between the two forks need to be changed as needed to make the tons of the two forks well balanced and not skewed, and one side of the item must be against the shelf. .
2. It is prohibited to work with a solitary fork or use a fork top or draw. In special conditions, security warning signs need to be set up to advise surrounding pedestrians. .
3. In the process of filling and unloading things, the forklift should be stopped with the brake. .
4. The speed of the automobile should be slow-moving and stable. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled items and hurt people. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as possible under the lots, and it ought to be kept in mind that the fork tip must not touch various other goods or things. The load ought to be maintained with minimal back tilt of the gantry to ensure that the lots does not slide in reverse. The pole can be tilted forward somewhat when the lots is lowered to enable very easy placement of the load and extraction of the forks. .
6. It is restricted to fork goods at high speed and hit tough things with the fork head. .
7. When the forklift is working, it is forbidden for people to stand around the fork, so regarding stay clear of the collapse of the goods and hurt people. .
8. Overwhelming is Electric Forklift Truck for Warehouse forbidden, and it is banned to use forks to lift personnel to participate in high-altitude procedures to stay clear of high-altitude dropping crashes. .
9. It is not allowed to use the brake inertia to slip, put, round or roll objects. .
10. It is not enabled to utilize forks to choose, transform pallet dump.

Leaving .
1. It is restricted to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you have to dump the goods or reduced the fork frame.
2. Pull the parking brake handle to dead or depress the emergency brake switch.
3. The engine is shut off and the power is cut off. (Except for special circumstances, such as the chauffeur does not leave the lorry's line of sight and does not exceed 1 minute).
4. Remove the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the appearance ought to be checked, and fuel, lubing oil and air conditioning water must be added.
2. Check the safety efficiency of beginning, running and stopping.
3. Check whether the lights and horn signals are complete and reliable.
4. Throughout the operation of the forklift, check Electric Forklift Truck for Warehouse whether the stress and temperature level are typical.
5. After the forklift is running, the external leak ought to also be examined and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine before leaving the vehicle;.
2. When you encounter a person before you during driving, you need to send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight ought to be 0.3 m ~ 0.4 m in the air;.
5. The turning should not be also sharp to avoid the propensity of " complimentary turning";.
6. Adding and down the slope must be slow and consistent, and no switching on the incline is allowed.
7. Do not drive throughout the gradient. When the slope is higher than 10%, the lorry must be driven in reverse when declining;.
8. When the forklift personnel bring the goods and move on, if they experience huge or heavy items and go to the motorist's line of sight, they must take the turning around exercise
.
The "Eight Prohibitions" need to be followed in the procedure.
1. Solitary fork operation is not enabled.
2. It is not permitted to lift the goods for far away driving.
3. It is not permitted to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and various other unsafe chemicals with forks.
5. It is not allowed to utilize inertia pressure to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll items.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly forbidden to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Vehicle parking is not allowed under the list below problems.
1. Contours, narrow roads, railway crossings;.
2. Sections with a longitudinal slope above 5%.
3. When there is an barrier on one side of the roadway, the opposite side of the section with the same length as the challenge must be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844